Tag Archives: binding

Adding a Binding Edge to the Antique Quilts

So, this is how I attach binding to a quilt – it is pretty easy after you have done it a couple of times –

I started with using the extra backing fabric from the two antique quilts I had sent out to the long arm quilter.  They always give you the remaining backing and batting from the project to use on another project or for doing a binding in the same fabric as the backing – that is if you bought enough!

After organizing the backing remnants, I am ready for the first step.

extra backing fabric

The first step is ironing to get the fabric free of wrinkles before cutting with the rotary cutter.

Cutting 2.5 inch strips
Cutting 2.5 inch strips

After ironing on a cotton setting with steam, I fold then cut off the rough edge about 1/4 inch so that all of the cuts from that point will be square.

DSCN0760

I first cut a 5 inch strip, then sub-cut 2.5 inch strips.

DSCN0761

The 2.5 inch strips are then sewn right-sides together at the ends in order to make one long strip that is 2.5 inches wide.

DSCN0762

This long strip is then folded in half length-wise and ironed before joining to the top side of the quilt.

DSCN0763 DSCN0764

I like to start sewing the binding onto the quilt about halfway down one of the sides.  I leave about 5 inches or so of binding unstitched as this will be necessary for joining the end of the binding in the last step.

DSCN0765

I sew the binding on without pinning- EEK!  To do this, I just lay the ironed binding flat on the quilt top with the fold to the inside of the quilt top and the edges lined up with the finished edge of the quilt and sew away.  I use the regular foot and a “heavy” setting for fabric on my machine with a stitch length of 2.5.

DSCN0766

When I get to the end of a side of the quilt, I stop about 1/4 inch away from the corner,  lift the needle, and cut the thread.

stopping 1/4 inch from the edge
stopping 1/4 inch from the edge
folding at the corner
folding at the corner

I then fold the long (not sewn on yet!)end of the binding strip up perpendicular to the current side, and then fold back down again along the new edge with a fold at the top of the new side.

DSCN0790

This technique leaves a fold at the top of the new side with a corner of fabric tucked into the fold which will allow you to get perfect mitered edges on both the front and the back of the quilt at each corner when you turn the binding to the back for hand stitching.

The last step is a little tricky, but thanks some excellent online tutorials, I think I have gotten the hang of it.  Go ahead and click on the link!!!! it really helps!

DSCN0770

As I am sewing down the last side of the quilt (back to when I started) I stop with about 5 to 7 inches of edge unsewn, then leave 10 inches of folded binding material unstitched. I find a place between the two ends of the binding edge where I would like them to meet! – Say hello to the beginning and the end of the binding strip!

At the point where they meet, take the extra binding from the starting edge and fold it back on itself – this is on the right side in the photo above.  I take the extra binding from the left side (where I just stopped) and fold it too, with the folds of both sides meeting in the middle of the 5-7 inches of un-sewn edge. See the picture above for this step.

DSCN0771

I cut the fabric on the right at the fold, then measure 2.5 inches from the fold on the left and cut there.  If your binding width is different, then add that amount to the end of the binding strip before you cut.  I just use the unfolded binding as a tool for measuring here.  I will cut the long end of the binding one binding width from the fold.  In the picture below, I would cut the bottom fabric at the point where it meets the right edge of the top fabric where my index finger is pointing.  This gives me the perfect measure of fabric for an exact fit along the edge. See the picture below.

DSCN0772

Now, take the right sides of the two binding edges UNFOLDED and place them perpendicular to each other and sew diagonally across the “T” to make a single piece that is the perfect length for your quilt. I would sew these two pieces together as they are placed below, starting at the bottom and sewing diagonally up. Click here for a tutorial.

DSCN0773

Once you have sewn this seam, trim away excess fabric ( the triangle on the right in the picture below) and re-fold the binding strip in half length-wise again and press that piece.  This length should fit exactly along the side of the quilt if you have measured carefully.

DSCN0774

Now, just place the last bit of binding on your quilt top edge to finish attaching the machine stitched top edge of the binding – see below.

– BUT we’re not done yet! It’s time to hand stitch the binding to the back of the quilt.

DSCN0775

I fold over the binding from the front of the quilt to the back and use a matching thread with tiny stitches that won’t be too easy to see.  One of my favorite brands of thread is Gutermann.

DSCN0777

This part takes awhile, so grab a cup of tea and sit down with your favorite music or TV show on – I can generally get this step done in an evening.

DSCN0779 DSCN0776 DSCN0823

This is the folded binding  at the corner.  I stitched to the end, and then fold the binding down on the next side, keeping a fold of fabric in the corner again.  This fold then makes a perfect 45 degree miter.

DSCN0822

Now, I stitch up the fold and then work down the next side of the quilt – attaching the binding to the back using small stitches with thread that matches the binding.

DSCN0824

This is a close up of the hand-stitched binding edge on the back.  This piece is now complete –

DSCN0825

– Let me know your thoughts about your favorite binding techniques and if you are a 1930’s fabric fan like me.